Worcester Greenstar Heatslave 18/25 Overview
The Worcester Greenstar Heatslave 18/25 is a floor‑standing oil‑fired condensing boiler delivering up to 18 kW. It supports conventional and room‑sealed flues‚ features a digital control panel‚ and offers high efficiency with low emissions. The user manual covers installation‚ operation‚ and maintenance. !

Safety Precautions and Warnings
Before installing or servicing the Worcester Greenstar Heatslave 18/25‚ read all safety instructions. The boiler operates on high‑pressure oil and hot gases; improper handling can cause burns‚ explosions‚ or carbon monoxide poisoning. Ensure the unit is placed on a level‚ stable surface‚ at least 1 m from walls and combustible materials. Keep all flues‚ vents‚ and condensate drains free of obstructions and check for leaks regularly. Use only the approved oil type and keep the storage tank sealed to prevent vapour release. The boiler must be connected to a grounded electrical supply; all wiring should be performed by a qualified electrician. Do not operate the unit while the control panel is open or the cabinet is removed. When the boiler is running‚ maintain adequate ventilation to avoid CO accumulation; install a CO detector in the same room as the boiler. The heating system should be inspected annually by a licensed professional‚ and any fault should be reported immediately. Never attempt to repair or modify the boiler yourself; only authorized service personnel may work on the internal components. Follow the manufacturer’s instructions for cleaning‚ oil refilling‚ and condensate removal. Failure to comply with these precautions may result in injury‚ property damage‚ or voided warranty. If you suspect a gas leak‚ carbon monoxide leak‚ or any abnormal operation‚ shut the boiler off‚ ventilate the area‚ and contact emergency services and the service centre. Always adhere to the manufacturer’s safety guidelines everywhere.

Installation Guidelines
Place the boiler on a level‚ stable surface‚ 1 m from walls. Connect the oil supply‚ flue‚ and condensate drain per the diagram. Ensure proper grounding and use a qualified electrician for wiring. Seal all joints‚ check for leaks‚ and verify ventilation before first start. Follow diagram. Check seal.
Site Preparation and Layout
Prior to installation‚ verify that the floor can support the boiler’s weight. A concrete slab‚ minimum 50 mm thick‚ is recommended. Position the unit at least 1 m from any combustible material and 0.5 m from the nearest wall to allow adequate airflow. The boiler’s weight is approximately 120 kg‚ so ensure the slab can handle this load.
Mark the exact location with a laser level‚ ensuring the boiler sits level to prevent uneven wear on the burner and condensate system; Install a non‑slip mat beneath the boiler to protect the floor and provide a stable base. Provide 0.3 m clearance on all sides for maintenance access and safety. Use a spirit level to double‑check the horizontal alignment before finalizing the position.
Provide a dedicated 30 A circuit breaker‚ and route cables through an insulated conduit protected from heat. The condensate drain must be directed to a suitable disposal point‚ with a check valve to prevent backflow. Ensure the flue pipe is routed vertically‚ with a minimum 1 m clearance from the boiler to the roof or chimney. All connections should be tightened to the manufacturer’s torque specifications to prevent leaks. Check grounding resistance meets specifications.
Install a spill containment tray beneath the oil inlet to capture accidental leaks. Verify all connections are secure‚ and perform a pressure test on the oil system before commissioning. This preparation ensures safe‚ efficient operation and compliance with local codes. After the pressure test‚ inspect the oil inlet for any signs of leakage.
Ensure the installation area has adequate ventilation to dissipate combustion gases. A minimum airflow of 0.2 m³/s is recommended; install a vent hood if required. Label all connections and keep a schematic diagram near the unit. Check that the vent hood is sealed to prevent drafts. The vent hood should be inspected annually for blockages and cleaned as necessary.
Maintain a dry‚ dust‑free environment; avoid corrosive substances that could damage the boiler. After assembly‚ perform a leak test on the flue and oil lines using a 1 bar pressure test for 15 min. Verify compliance with BS 6858 and local building regulations. Record all measurements and test results in the installation log for future reference. Store the log safely and.

Flue Connection and Sealing
Connect the flue pipe to the boiler’s outlet with the supplied stainless‑steel coupling. Match the pipe diameter to the boiler’s spec: 150 mm for conventional‚ 100 mm for room‑sealed. Tighten all joints to 12 Nm torque. Seal the flange with high‑temperature silicone‚ apply a continuous bead‚ smooth with a brush‚ and let cure 24 h before use.
For conventional flues‚ route the pipe vertically‚ keeping a 1 m clearance from the boiler to the roof or chimney. Insulate with a 2 mm sleeve‚ secured every 30 cm with heat‑resistant tape. For room‑sealed flues‚ run the pipe horizontally‚ 0.5 m from combustibles‚ supported every 1.5 m with stainless brackets.
Check the flue alignment with a level; any tilt can cause back‑pressure and reduce combustion efficiency. Inspect for cracks or corrosion before mounting. Replace damaged sections immediately. After assembly‚ perform a 1 bar pressure test for 15 minutes to confirm integrity‚ and log the results.
Install a draft regulator at the flue’s exit to maintain optimal combustion. Set it to 0.5 kPa‚ per the boiler’s range. Verify operation by observing flame stability during a short test burn; adjust if the flame is too high or low. Protect the regulator from condensation with a condensate drain line and check valve.
Finally‚ seal all flue connections with a metal gasket and a 2 mm high‑temperature sealant. Inspect the gasket for wear and replace if needed. Keep the flue area clear of debris‚ and ensure the vent hood is clean and functional. This sealing process guarantees safe‚ efficient operation and compliance with local safety standards. Maintenance records must be kept for five years and checks;
Electrical Wiring and Connection
Before connecting the Worcester Greenstar Heatslave 18/25‚ verify that the supply voltage matches the boiler’s rated 230 V/50 Hz. Use a double‑insulated‚ 3‑phase‚ 4‑wire cable (cable type 4 AWG) with a minimum 2.5 mm² cross‑section. Route the cable away from heat sources and ensure it is secured with cable ties every 1 m.
At the boiler‚ connect the live (L)‚ neutral (N)‚ and earth (PE) conductors to the corresponding terminals marked on the control panel. Tighten all screws to 12 Nm torque. The boiler requires a dedicated 16 A circuit breaker; the breaker must be listed for 230 V and have a residual‑current protection (RCD) of 30 mA.
Grounding is critical: attach the earth conductor to the boiler’s metal frame using a 10 mm² copper strap. Verify continuity with a multimeter; resistance should be below 0.1 Ω. If the boiler is installed in a wet area‚ use a GFCI breaker to protect against shock.
After wiring‚ perform a voltage test: the live should read 230 V to neutral‚ and the earth should show continuity to the frame. Check for any loose connections by gently tugging on each cable; If the boiler fails to start‚ inspect the control board for a blown fuse or a tripped breaker.

Document all wiring details‚ including cable lengths‚ breaker numbers‚ and grounding points‚ in the installation log. This record is essential for future maintenance and compliance inspections. Follow local electrical codes and manufacturer guidelines to ensure safe‚ reliable operation. All connections must be inspected quarterly and verified!

Commissioning and Start‑Up
Begin by checking all safety interlocks‚ ensuring the boiler is on a level surface. Power on the main switch‚ then set the thermostat to a high temperature. Observe the ignition sequence; the flame should stabilize within 30 s. Verify pressure gauges‚ and record the initial readings for futurereference.
Initial Testing and Calibration
After powering the boiler and verifying ignition‚ perform initial tests to confirm proper operation. Check the pressure gauge to ensure the system is within the manufacturer‑specified range (typically 1.0–1.5 bar). Verify the flame sensor by observing the LED indicator; it should remain steady once the flame is established. Run a short test cycle at the lowest set‑point to confirm the circulation pump engages and the return temperature rises to the expected level. Adjust the high‑limit temperature setting on the control panel to match the boiler’s rated output (18 kW). Record all initial readings in the log book and compare them with the factory calibration data. If any parameter deviates beyond the acceptable tolerance‚ consult the troubleshooting section before proceeding with full operation.
Perform a flue integrity check by inspecting the flue connections for leaks and ensuring the flue pressure gauge reads within the specified range; Verify the oil pressure by checking the gauge on the oil supply line; it should be between 30–35 psi. Test the safety cut‑off by manually triggering the high‑temperature alarm and confirming the boiler shuts down within the required time. Finally‚ calibrate the temperature sensors by comparing the boiler’s internal readings with a calibrated external thermometer; adjust the sensor offset on the control panel if necessary to achieve accurate temperature control.
Once checks are satisfactory‚ set the boiler to normal mode and monitor for 30 min to ensure stable operation. Verify the safety cut‑off activates within the specified time and confirm the pressure gauge remains within the safe range during the test. Record all observations in the log daily!!! OK

Operation and Controls
The boiler’s digital panel offers set‑point adjustment‚ safety limits‚ and diagnostics. Use the main power switch‚ set desired temperature‚ and watch the flame indicator. The system auto‑regulates pressure and temperature for efficient‚ quiet operation.LCD shows all data

Control Panel Functions and Settings
The Worcester Greenstar Heatslave 18/25 is equipped with a clear‚ backlit LCD that displays all critical operating data. The panel is divided into several sections: the main display‚ the control buttons‚ and the diagnostic area. Users can navigate through the menu using the arrow keys and confirm selections with the enter button. The following functions are available:
- Set‑point Temperature: Adjust the desired room temperature with the +/- keys. The boiler will automatically modulate the flame to maintain this set‑point‚ ensuring consistent comfort while optimizing fuel consumption.
- Pressure and Temperature Limits: On the main screen the current water pressure and temperature are shown. The system will shut down if the pressure exceeds the upper safety limit or if the temperature drops below the minimum threshold‚ protecting the boiler from damage.
- Flame Status Indicator: A dedicated LED shows whether the flame is on‚ off‚ or in a fault condition. This visual cue helps users quickly identify operational status or troubleshoot issues.
- Diagnostic Codes: When a fault occurs‚ the panel displays a numeric code that corresponds to a specific problem (for example‚ low oil pressure‚ sensor failure‚ or flue blockage). The user manual contains a reference table for interpreting these codes.
- Manual/Automatic Mode: The switch allows the user to toggle between manual mode‚ where the flame can be controlled directly‚ and automatic mode‚ where the boiler follows the set‑point and safety limits.
- Timer and Scheduling: The built‑in timer lets users program heating periods for weekdays and weekends. This feature reduces energy consumption during off‑hours and can be adjusted from the main menu.
- Remote Connectivity (Optional): When paired with the Worcester Smart Connect module‚ the boiler can be monitored and controlled via a smartphone app‚ providing remote temperature adjustments and status alerts.
To ensure optimal performance‚ review the displayed parameters regularly and consult the troubleshooting section if any abnormal readings appear. The panel also offers a self‑diagnostic routine that can be initiated from the menu‚ which checks all sensors and safety devices for proper operation.

Maintenance and Servicing
Routine maintenance ensures longevity. Clean the burner annually‚ inspect the oil filter‚ and check the flue for blockages. Lubricate moving parts‚ verify pressure gauges‚ and test safety valves. Service every 12 months by a qualified technician per the manual. Check the manual for detailed procedures.
Regular Cleaning and Inspection
Regular cleaning and inspection are essential to maintain the Worcester Greenstar Heatslave 18/25’s performance. Follow the manufacturer’s schedule: wipe the exterior with a damp cloth‚ inspect the oil filter and replace it if clogged. Clean the combustion chamber with a soft brush‚ ensuring no debris remains that could affect flame stability. Inspect the flue system for cracks‚ corrosion‚ or blockages; a sealed flue must remain airtight to prevent back‑drafts. Verify the pressure gauge accuracy and the operation of the safety valve; any deviation should be corrected by a licensed technician. Test the electrical connections for loose terminals and corrosion‚ tightening as needed. Finally‚ run a short trial burn to confirm the boiler ignites correctly‚ the flame is steady‚ and the heat output matches the rated 18 kW. Document each inspection in a logbook‚ noting dates‚ findings‚ and actions taken. This routine care extends the boiler’s lifespan‚ improves efficiency‚ and reduces the risk of costly repairs or hazardous incidents. Inspect the oil tank for leaks and ensure the level is within the range. Examine the heat exchanger for corrosion or scaling; a clean exchanger maximizes heat transfer. Verify the thermostat calibration by comparing the set temperature with the room temperature. Check the condensate drain for clogs and ensure it discharges properly. Finally‚ review the boiler’s log for any fault codes and address them promptly. Check pressure. Record all findings for reference!!

Troubleshooting Common Issues
When the Worcester Greenstar Heatslave 18/25 fails to start‚ check the oil supply and pressure. A low oil level or blocked filter can prevent ignition. Verify the ignition switch is receiving power and that the flame sensor reads correctly; a dirty sensor may trigger a fault code. If the boiler displays error code 12‚ inspect the pressure gauge for a low reading; the system may be under‑pressurised due to a leak or a faulty pressure relief valve. For error code 23‚ the condensate drain is likely clogged; clear the drain and ensure the condensate pipe is properly sloped. If the boiler shuts down during operation‚ examine the flue for obstructions or a collapsed vent. A blocked flue can cause back‑draft and trigger the safety cut‑off. Check the safety valve and the thermal cut‑off switch; a stuck valve can cause the unit to stop. For intermittent operation‚ confirm that the thermostat is set correctly and that the room temperature sensor is functioning; a mis‑calibrated sensor can cause the boiler to cycle irregularly. If the boiler runs but delivers insufficient heat‚ inspect the heat exchanger for scaling or corrosion; cleaning or replacing the exchanger may be required. Finally‚ always refer to the fault code list in the user manual and follow the recommended corrective actions. If the problem persists‚ contact a qualified service technician to perform a detailed diagnostic and repair. The routine checks above will help maintain reliable operation and prevent costly downtime. Regularly updating the firmware and ensuring the control panel displays no error messages will further reduce downtime. Additionally‚ schedule annual professional servicing to verify all safety mechanisms‚ check the condensate drain‚ and clean the heat exchanger to maintain optimal efficiency.